The Ebay manifolds to get(td04 manifolds) - Page 2 - 3000GT/Stealth International Message Center

SkortchGT · 04-01-2008, 10:24 AM

Subscribed

StXFoo · 04-06-2008, 04:43 PM

Any luck this weekend?

SPYDERTT · 04-08-2008, 03:58 PM

I bought an identical set of headers off of Ebay. The seller said he didnt need them , i'm sure he saw how junk they were and didn't want them. I had to grind 3 exhaust studs, no big deal, the flanges were warpped over .030 , the front turbo holes need slotted, there is no way to get a nut on one turbo stud ( it is too close to the weld), the front pre cat eliminator ( I got off ebay) wont fit ( it hits header ) so I tryed my gutted pre cat and it hits too. The factory braces wont fit , so even if I grind ,chop and cus enough I doubt my downpipe will fit

mikes2nd · 04-13-2008, 10:40 AM

Im waiting on my 3sx rod. So far so good, the manifolds look good so far. They angle correctly.

But test fit the back one. I had them ground flat.

The bottom studs had to be taken down a bit. And the turbo side I filed flat.

I bought 2 sets. The one needed ground. the ones with "top speed" tags on them were the better of the 2. They actually were flat but i had them done also.

The front will need a little bit taken off the stud in the middle.

Monster Stealth · 04-13-2008, 10:46 AM

Subscribed

3KGT2NV · 04-13-2008, 11:09 AM

well if this does work out and anyone wants a set ill sell mine for 200 plus ship since they dont work with the soon to be td05 setup

amiturbo · 04-14-2008, 09:11 AM

does urs come with precats or no?

mikes2nd · 05-07-2008, 10:37 AM

putting them on. Had to forego one washer on the rear manifold.

Front had to take a little off. Front turbo having some space issues. Going to be putting on custom brackets to mimic stock supports on turbos.

Had to shift the turbo around a little and working out how to get the bolts on.

Im sure these are similar to DNP issues. Full install pics coming this weekend.

mikes2nd · 05-07-2008, 05:16 PM

more pics

mikes2nd · 05-09-2008, 09:43 PM

using the factory braces

This is taking a fair amount of time to get it all nice. Im sure DNP is probably the same..

04-01-2008, 10:24 AM	#11 (permalink)
SkortchGT Warning: I'm an asshole Join Date: Jan 2002 Location: Lehigh Valley, PA Drives: 1992 3000GT VR4 Trader Rating: (10)	Re: The Ebay manifolds to get(td04 manifolds) Subscribed __________________ 1992 3000GT VR4 --Completely rebuilt 5/06-4/07. Everything new. For a list see: http://www.3si.org/forum/showthread.php?t=372579 --First time on dyno: 364AWHP@16psi with a 10.3AFR (now tuned at 11.4-11.6 with timing control, time for another dyno run soon) --Mods: DR Stage I heads, 3rd gen lifters, TD04L 13Gs, DSM SMICs, PTE 550s, Apexi SAFC, Apexi SITC, Walbro FP, IPO hotwire, Robbeck adapter & AEM FPR, 3SX underhood fuel gauge, 3SX fuel rail loop, DN Y-pipe, HKS SSQ BOV, K&N FIPK, Greddy Profec Spec S, AEM WB02, Autometer C2 boost, egt, oil press & water temp gauges, MSD wires, NGK BCP7ES's, TEIN FLEX coilovers, Maximal performance control arms, solid engine mounts & powdercoating, RPS Streetmax Clutch, RPS Flywheel, NBT Tranny (cryotreated OS, shift forks & rails), updated speedo gear, solid shifter bushings, full 2nd gen brake conversion, 3SX SS brake & clutch lines, Carbotech Panther+ pads in the front & Bob Cats in the rear, 3SX clutch vac delete, EGR delete, vac reduction, Ebay DP, gutted pre cats, Bronze FN01RCs 5Zigen 18x8.5 + 30 offset, Pirelli P-Zeros, engine dress up kit, Bigtyla ground wire kit. --Daily Driver: 98 Malibu, 4cyl, auto

04-06-2008, 04:43 PM	#12 (permalink)
StXFoo Verified Seller Join Date: Jul 2005 Location: Cincinnati, Ohio Trader Rating: (33)	Re: The Ebay manifolds to get(td04 manifolds) Any luck this weekend? __________________ Vaib *Ride Of The Month - MAY 2008!*

04-08-2008, 03:58 PM	#13 (permalink)
SPYDERTT Forum Member Join Date: Feb 2005 Location: Kansas Drives: 95 Spyder VR4 Trader Rating: (1)	Re: The Ebay manifolds to get(td04 manifolds) I bought an identical set of headers off of Ebay. The seller said he didnt need them , i'm sure he saw how junk they were and didn't want them. I had to grind 3 exhaust studs, no big deal, the flanges were warpped over .030 , the front turbo holes need slotted, there is no way to get a nut on one turbo stud ( it is too close to the weld), the front pre cat eliminator ( I got off ebay) wont fit ( it hits header ) so I tryed my gutted pre cat and it hits too. The factory braces wont fit , so even if I grind ,chop and cus enough I doubt my downpipe will fit

04-13-2008, 11:09 AM	#16 (permalink)
3KGT2NV Verified Seller Join Date: May 2007 Location: poughkeepsie, NY Drives: 1994 3kgt vr-4 Trader Rating: (11)	Re: The Ebay manifolds to get(td04 manifolds) well if this does work out and anyone wants a set ill sell mine for 200 plus ship since they dont work with the soon to be td05 setup __________________ Board at work check out these free games http://s3.gladiatus.us/game/c.php?uid=89364 or http://astroempires.com

04-14-2008, 09:11 AM	#17 (permalink)
amiturbo Banned from Classifieds Join Date: Jun 2007 Location: New Port Richey,Fl Drives: 93 dodge stealth es Trader Rating: (3)	Re: The Ebay manifolds to get(td04 manifolds) does urs come with precats or no?

Sponsored Links
3000GT/Stealth International Message Center Advertisement

05-07-2008, 10:37 AM	#18 (permalink)
mikes2nd Regulator... Join Date: Jul 2002 Location: OH Trader Rating: (30)	Re: The Ebay manifolds to get(td04 manifolds) putting them on. Had to forego one washer on the rear manifold. Front had to take a little off. Front turbo having some space issues. Going to be putting on custom brackets to mimic stock supports on turbos. Had to shift the turbo around a little and working out how to get the bolts on. Im sure these are similar to DNP issues. Full install pics coming this weekend.