MMCd Logger New Features and Sensors Archive Latest Information
16-4-05 Posted V1.8g (see below)
Starting this thread to review MMCd bugs and discuss possible new features. I would also like to see if there are other 3SI members interested in doing SW development. (Dev environment is free and takes less than an hour to set up.)
My goal is to periodically summarize feedback / posts on this page.
NEW SOFTWARE FEATURES
1. Auto Logging on Event (cbatters - done)
2. Peak - Hold (cbatters - done)
3. Upload / Convert to CSV (Shawn ????)
4. Address data scaling issues in log files
5. Big Number Mode (TurboBob?)
6. Graphical Gages
7. User Scaling/Config for Custom Inputs
8. User configuration for graph scaling (colors/scaling/offset)
9. User config for all sensors (colors/scaling)
10. User defined log rates / prelog / postlog
11. User defined graphical display time resolution
12. User defined alarm tones
13. Graphical alarm alert
Other suggestions...
HSLogger Project
Interface for adding additional inputs to the MMCd logger. New inputs include:
o Boost (x1) (Using either 2.5 or 3.0 MAP sensor)
o Wideband O2 (x1)
o Oil Pressure (x1)
o Fuel Pressure (x1)
o Intake Manifold Air Temp (x1)
o 0-15V input (x1) (Fuel pump voltage)
o EGT (x1)
o Other
o Vehicle speed (1) and derived calculations
- MPG
- 0-60 timing
- AWD HP
Models / Pricing
Planning to offer three different models of the HSLogger.
HSLogger Base - Fixes baud rate / RS232 level issues to allow compatibility with ALL Palm devices and includes Speed/Odometer input for performance / MPG calculations. You can also log boost with the unused EGRT input. (~$100)
HSLogger Exp - All of the Base unit features plus six 0-5V inputs (Pressure/Boost/Wideband O2 etc from existing sensors/gages - any 0-5V signal) (~$175)
HSLogger Deluxe - All of the Exp unit features plus higher resolution for low level inputs with signal conditioning for direct connection to sensors. Deluxe version has an "analog front end" that provides amplification, filtering, sensor excitation for direct connection to EGT Thermocouples, oil/fuel pressure senders, etc. (~$250)
I believe the Base unit is is competitively priced based on quality passive cables for $75 from Mirage or $150 for PocketLogger SW + Cable. (In my not so humble opinion, MMCd now runs circles around the PocketLogger SW.)
LINKS
Dmitry's Site http://mmcd.meditprofi.ru/
Protocol Info http://www.syndicate.evilsoft.org/projects/DSMDatalogger/Datalogger_Protocol.html
Boost Logging http://www.3si.org/forum/showthread.php?t=202062&highlight=mmcd
Intake Temp Thread http://www.3si.org/forum/showthread.php?t=217333&page=1&pp=10
Intake Air Temp Research http://www.3si.org/forum/showthread.php?t=98661&highlight=plenum+temperature
Horsepower Calculation http://www.newcovenant.com/speedcrafter/calculators/rollinghorsepower.htm
Boost Controller Thread http://www.3si.org/forum/showthread.php?t=222166
Injector Cleaning Service http://cruzinperformance.com
BlackStone Oil Testing http://www.blackstone-labs.com
Intake Leak Testing http://www.3si.org/forum/showthread.php?t=200417
Inline Spark Tester http://www.3si.org/forum/showpost.php?p=2433324&postcount=25
Rolling Resistance http://www.3si.org/forum/showpost.php?p=3137280&postcount=203
O2 Sensor Wiring / Test http://www.3si.org/forum/showthread.php?p=712579&highlight=sensor+wiring+green+yellow#post712579
Air Filter Restriction / MPG - http://www.3si.org/forum/showthread.php?t=294215&highlight=dirty+air+filter
Data Loggin FAQ - http://www.vfaq.com/TMO/
PocketLogger FAQ - http://www.hywell.org/plhelp/data.html
Online Manual - http://www.ecanfix.com/users/manualcd/gift/3s/
LATEST VERSIONS
MMCd V1.8g - http://www.3si.org/forum/attachment.php?attachmentid=49809
MMcd V1.6n - http://www.3si.org/forum/attachment.php?attachmentid=39998
MMCd Tools (SPoulson) http://mmcdtools.sourceforge.net/
MMCd Tools - Bugfix (.2c) http://lancache.com/images/MMCdTools-0.2c.exe
SENSORS
EGT Probes - http://www.teamrip.com/accessories.html
K Tc Probes - http://www.thermoworks.com/products/probe/tc_wire.html
Easy Fuel Pressure Install- http://www.3si.org/forum/showthread.php?t=213356&highlight=easy+fuel
VDO Pressure Senders - http://www.continentalimports.com/vdo_send_press.html
Fuel Pressure Sender - http://www.dakotadigital.com/Detail.cfm/-/Category=106/PartNumber=SEN-10-2/product.htm
DEVELOPMENT LINKS
PRC Setup for Windows - http://prc-tools.sourceforge.net/install/cygwin.html
Palm SDK for PRC - http://spp.palmos.com/iws/logon.do?...os-sdk-5.0r3-1.tar.gz&back=dl_sdks/sdk50.html
Handspring SDK -
Pilot Hack http://www.massena.com/darrin/pilot/PilotHackTutorial.htm
Palm Simulator - http://www.cs.trinity.edu/ftp/pub/w2k-software/Palm/Simulator/Palm_OS_5_Simulator_Rel.zip
Palm Simulator (PalmOS Site) - http://www.palmos.com/dev/tools/simulator/
Palm Emulator (PalmOS Site) - http://www.palmos.com/dev/tools/emulator/
FAQ - Tuning Information
MMCd Info - http://mmcdlogger.sourceforge.net/#Features
MMCd Tips - Remember to click on the "i" in the config dialogs for more info
TMO Faq - http://www.vfaq.com/TMO/Tuning-Tips.htm
PLogger Faq - http://www.pocketlogger.com/index.php?pid=params&type=dsm
Q1 - What do the letters mean in FLAG0 and FLAG2
Flag 02 status bits
A - Air conditioning relay
F - Fuel pump relay
B - Boost related ???
Flag 00 status bits
T - TDC sensor
S - Power Steering Pressure SW
A - AC switch
N - Neutral
I - Idle switch
Q2 - How do I view MMCd logs on a PC?
MMCd has built in support to upload logs using the Palms archive file capability by simply flagging the log files in MMCd. Files will automatically get uploaded to Palm User - Archive directory on the PC the next time you hotsync.
Simple solution for reviewing logs is to download the PalmSimulator which allows you to run MMCd on the PC. (Just drag MMCd program and log files to the simulator window.)
The other choice is to download MMCdTools which provides a conduit for xfer of logs files as well as conversion of MMCd log format to CSV.
http://mmcdtools.sourceforge.net/
SUMMARY OF CHANGES
KNOWN ISSUES:
Buttons/checkbox controls cause delays in log sampling rate
INVESTIGATION:
Min/Max button
User defined prelog / postlog times
Consider adding default Autolog triggers
Correct slug for EGRT WBO2 inputs - currently hard coded as MAP
Need to confirm Boost solenoid status display
Need to define/implement new log format (mS resolution / Integer / Long / Char )
Scaling for AFR input - Changed in 1.6N
Old 0-5V = 10.0 - 20.0 AFR
New 0-5V = 8.0 - 22.0 AFR
Configurable option for 3S versus DSM mode
- Timing
- Other differences?
16-4-05 Posted V1.8g (see below)
Starting this thread to review MMCd bugs and discuss possible new features. I would also like to see if there are other 3SI members interested in doing SW development. (Dev environment is free and takes less than an hour to set up.)
My goal is to periodically summarize feedback / posts on this page.
NEW SOFTWARE FEATURES
1. Auto Logging on Event (cbatters - done)
2. Peak - Hold (cbatters - done)
3. Upload / Convert to CSV (Shawn ????)
4. Address data scaling issues in log files
5. Big Number Mode (TurboBob?)
6. Graphical Gages
7. User Scaling/Config for Custom Inputs
8. User configuration for graph scaling (colors/scaling/offset)
9. User config for all sensors (colors/scaling)
10. User defined log rates / prelog / postlog
11. User defined graphical display time resolution
12. User defined alarm tones
13. Graphical alarm alert
Other suggestions...
HSLogger Project
Interface for adding additional inputs to the MMCd logger. New inputs include:
o Boost (x1) (Using either 2.5 or 3.0 MAP sensor)
o Wideband O2 (x1)
o Oil Pressure (x1)
o Fuel Pressure (x1)
o Intake Manifold Air Temp (x1)
o 0-15V input (x1) (Fuel pump voltage)
o EGT (x1)
o Other
o Vehicle speed (1) and derived calculations
- MPG
- 0-60 timing
- AWD HP
Models / Pricing
Planning to offer three different models of the HSLogger.
HSLogger Base - Fixes baud rate / RS232 level issues to allow compatibility with ALL Palm devices and includes Speed/Odometer input for performance / MPG calculations. You can also log boost with the unused EGRT input. (~$100)
HSLogger Exp - All of the Base unit features plus six 0-5V inputs (Pressure/Boost/Wideband O2 etc from existing sensors/gages - any 0-5V signal) (~$175)
HSLogger Deluxe - All of the Exp unit features plus higher resolution for low level inputs with signal conditioning for direct connection to sensors. Deluxe version has an "analog front end" that provides amplification, filtering, sensor excitation for direct connection to EGT Thermocouples, oil/fuel pressure senders, etc. (~$250)
I believe the Base unit is is competitively priced based on quality passive cables for $75 from Mirage or $150 for PocketLogger SW + Cable. (In my not so humble opinion, MMCd now runs circles around the PocketLogger SW.)
LINKS
Dmitry's Site http://mmcd.meditprofi.ru/
Protocol Info http://www.syndicate.evilsoft.org/projects/DSMDatalogger/Datalogger_Protocol.html
Boost Logging http://www.3si.org/forum/showthread.php?t=202062&highlight=mmcd
Intake Temp Thread http://www.3si.org/forum/showthread.php?t=217333&page=1&pp=10
Intake Air Temp Research http://www.3si.org/forum/showthread.php?t=98661&highlight=plenum+temperature
Horsepower Calculation http://www.newcovenant.com/speedcrafter/calculators/rollinghorsepower.htm
Boost Controller Thread http://www.3si.org/forum/showthread.php?t=222166
Injector Cleaning Service http://cruzinperformance.com
BlackStone Oil Testing http://www.blackstone-labs.com
Intake Leak Testing http://www.3si.org/forum/showthread.php?t=200417
Inline Spark Tester http://www.3si.org/forum/showpost.php?p=2433324&postcount=25
Rolling Resistance http://www.3si.org/forum/showpost.php?p=3137280&postcount=203
O2 Sensor Wiring / Test http://www.3si.org/forum/showthread.php?p=712579&highlight=sensor+wiring+green+yellow#post712579
Air Filter Restriction / MPG - http://www.3si.org/forum/showthread.php?t=294215&highlight=dirty+air+filter
Data Loggin FAQ - http://www.vfaq.com/TMO/
PocketLogger FAQ - http://www.hywell.org/plhelp/data.html
Online Manual - http://www.ecanfix.com/users/manualcd/gift/3s/
LATEST VERSIONS
MMCd V1.8g - http://www.3si.org/forum/attachment.php?attachmentid=49809
MMcd V1.6n - http://www.3si.org/forum/attachment.php?attachmentid=39998
MMCd Tools (SPoulson) http://mmcdtools.sourceforge.net/
MMCd Tools - Bugfix (.2c) http://lancache.com/images/MMCdTools-0.2c.exe
SENSORS
EGT Probes - http://www.teamrip.com/accessories.html
K Tc Probes - http://www.thermoworks.com/products/probe/tc_wire.html
Easy Fuel Pressure Install- http://www.3si.org/forum/showthread.php?t=213356&highlight=easy+fuel
VDO Pressure Senders - http://www.continentalimports.com/vdo_send_press.html
Fuel Pressure Sender - http://www.dakotadigital.com/Detail.cfm/-/Category=106/PartNumber=SEN-10-2/product.htm
DEVELOPMENT LINKS
PRC Setup for Windows - http://prc-tools.sourceforge.net/install/cygwin.html
Palm SDK for PRC - http://spp.palmos.com/iws/logon.do?...os-sdk-5.0r3-1.tar.gz&back=dl_sdks/sdk50.html
Handspring SDK -
Pilot Hack http://www.massena.com/darrin/pilot/PilotHackTutorial.htm
Palm Simulator - http://www.cs.trinity.edu/ftp/pub/w2k-software/Palm/Simulator/Palm_OS_5_Simulator_Rel.zip
Palm Simulator (PalmOS Site) - http://www.palmos.com/dev/tools/simulator/
Palm Emulator (PalmOS Site) - http://www.palmos.com/dev/tools/emulator/
FAQ - Tuning Information
MMCd Info - http://mmcdlogger.sourceforge.net/#Features
MMCd Tips - Remember to click on the "i" in the config dialogs for more info
TMO Faq - http://www.vfaq.com/TMO/Tuning-Tips.htm
PLogger Faq - http://www.pocketlogger.com/index.php?pid=params&type=dsm
Q1 - What do the letters mean in FLAG0 and FLAG2
Flag 02 status bits
A - Air conditioning relay
F - Fuel pump relay
B - Boost related ???
Flag 00 status bits
T - TDC sensor
S - Power Steering Pressure SW
A - AC switch
N - Neutral
I - Idle switch
Q2 - How do I view MMCd logs on a PC?
MMCd has built in support to upload logs using the Palms archive file capability by simply flagging the log files in MMCd. Files will automatically get uploaded to Palm User - Archive directory on the PC the next time you hotsync.
Simple solution for reviewing logs is to download the PalmSimulator which allows you to run MMCd on the PC. (Just drag MMCd program and log files to the simulator window.)
The other choice is to download MMCdTools which provides a conduit for xfer of logs files as well as conversion of MMCd log format to CSV.
http://mmcdtools.sourceforge.net/
SUMMARY OF CHANGES
KNOWN ISSUES:
Buttons/checkbox controls cause delays in log sampling rate
INVESTIGATION:
Min/Max button
User defined prelog / postlog times
Consider adding default Autolog triggers
Correct slug for EGRT WBO2 inputs - currently hard coded as MAP
Need to confirm Boost solenoid status display
Need to define/implement new log format (mS resolution / Integer / Long / Char )
Scaling for AFR input - Changed in 1.6N
Old 0-5V = 10.0 - 20.0 AFR
New 0-5V = 8.0 - 22.0 AFR
Configurable option for 3S versus DSM mode
- Timing
- Other differences?