3SX TD05 Kit install? - Page 8 - 3000GT/Stealth International Message Center

ozdave2 · 06-30-2008, 10:34 PM

Quote:

Originally Posted by Import Power

Wastegate pressure-14psi
maTT's car
3SX TD05 kit
660 inj
MafT
SAFC II
DSM SMICS w/stock pipes
PST 1 pc CF driveshaft
stock cams slight pocket port on heads stock valves
Walbro pump
3" exhaust

Looks like MaTT is getting to boost limit around 3500 rpm; I am only around 7 psi; what would that indicate. regards

ozdave2 · 07-01-2008, 01:26 AM

Actually not getting 5 psi T 3500 RPM!

Import Power · 07-01-2008, 03:53 AM

Quote:

Originally Posted by ozdave2

Looks like MaTT is getting to boost limit around 3500 rpm; I am only around 7 psi; what would that indicate. regards

Matt's car is odd, we aren't sure why it boosts faster and has more low end torque than most any other TD05 car we have tested. Could be the pocket ported only heads with stock cams?

94TTinga · 07-01-2008, 04:56 AM

I am hitting 16 psi (what I have it set to) @ 3650-3700. You can feel it start building @ 3-3200 and then it just sets you back in the seat when it all kicks in.

Shane

ozdave2 · 07-16-2008, 07:37 PM

Looks like I have found my problem. Both intercoolers were leaking so system was not holding pressure. Also found all four cams out by one tooth. Has to be retuned. Will let you know results. Thanks for everyone's help.

Import Power · 07-17-2008, 04:23 AM

Quote:

Originally Posted by ozdave2

Looks like I have found my problem. Both intercoolers were leaking so system was not holding pressure. Also found all four cams out by one tooth. Has to be retuned. Will let you know results. Thanks for everyone's help.

That will do it.

Keep us updated!

streamlnauto · 08-22-2008, 10:35 PM

Just about ready to fire it up, its been 3 years, I am excited, yet nervous all at the same time-

Import Power · 08-23-2008, 03:38 AM

Quote:

Originally Posted by streamlnauto

Just about ready to fire it up, its been 3 years, I am excited, yet nervous all at the same time-

3 yrs? Wow..Let us know how it goes! She will be a hoot to drive after not having her for 3 years.

-Chris

xteekayx · 08-23-2008, 08:24 PM

has anyone thought about getting the header flanges cut because they prolly got warped while welding?...

Import Power · 08-24-2008, 07:53 AM

Quote:

Originally Posted by xteekayx

has anyone thought about getting the header flanges cut because they prolly got warped while welding?...

We install a number of the kits at the shop. They are normally as flat as any other aftermarket header flange we run across. But with any aftermakrket header there are a few out there that are a little off. I have take a torch to a few while in the press and nudged them back to flat. They were so slight a mill could have cleaned it up to straight.

07-01-2008, 01:26 AM	#72 (permalink)
ozdave2 Forum Member Join Date: Nov 2007 Location: GEELONG VICTORIA AUS Drives: 92 STEALTH TT Trader Rating: (1)	Re: 3SX TD05 Kit install? Actually not getting 5 psi T 3500 RPM!

07-01-2008, 04:56 AM	#74 (permalink)
94TTinga 2nd Place NG08 DRAGS Join Date: Sep 2003 Location: CARROLLTON,GA Drives: 1994 Stealth TT Trader Rating: (9)	Re: 3SX TD05 Kit install? I am hitting 16 psi (what I have it set to) @ 3650-3700. You can feel it start building @ 3-3200 and then it just sets you back in the seat when it all kicks in. Shane __________________ 1994 Stealth TT, 1 of 10, Mods- 3.1l 8.5:1 ross pistons, pauter rods, gtpro head gaskets, apr studs, DR stage 3 heads with street grind cams, high rev springs and 3gen lifters ,3SX TD05 kit with EVO III 16G's, PTE 680cc Injectors, SAFC II, Emanage Ultimate, Denzo Fuel Pump, LM-1 Wideband, Intrax Springs, DN Downpipe, Alamosports SMIC's and Hardpipes,Blitz DSBC Boost Controller, K & N Aircharger, 3" split dual exhaust- Straight pipes, Greddy Type-S BOV, Fidanza Flywheel, SS Brakelines,Hotwired fuel pump

07-16-2008, 07:37 PM	#75 (permalink)
ozdave2 Forum Member Join Date: Nov 2007 Location: GEELONG VICTORIA AUS Drives: 92 STEALTH TT Trader Rating: (1)	Re: 3SX TD05 Kit install? Looks like I have found my problem. Both intercoolers were leaking so system was not holding pressure. Also found all four cams out by one tooth. Has to be retuned. Will let you know results. Thanks for everyone's help.

08-22-2008, 10:35 PM	#77 (permalink)
streamlnauto Forum Member Join Date: May 2007 Trader Rating: (1)	Re: 3SX TD05 Kit install? Just about ready to fire it up, its been 3 years, I am excited, yet nervous all at the same time-

08-23-2008, 08:24 PM	#79 (permalink)
xteekayx Keeps 3Ses on the road Join Date: Oct 2003 Location: North Jersey Drives: anything that rolls Trader Rating: (14)	Re: 3SX TD05 Kit install? has anyone thought about getting the header flanges cut because they prolly got warped while welding?... __________________ Toy: -= '95 RT/TT =-

Sponsored Links
3000GT/Stealth International Message Center Advertisement