---===The Official MAFT-Pro Thread===---

[Rogue_Ant]

Jon, you can try Bob's .bin. Just make sure to adjust the mainscale to account for your injectors. (I would try -20 to start)
If your EGT is a k-type thermocouple, then you can log it with the T-Pro. But you will need the EGT amplifier found at fullthrottlespeed.com


-Rogue

[JonVr4]

I also dont have the timing wired or anything, i should just load this bin and adjust the main scale and be ready to go? The bin loads the pt tracking/setup/configure/ and everything else?

[3000GT MR]

Originally Posted by Rogue_Ant

Jon, you can try Bob's .bin. Just make sure to adjust the mainscale to account for your injectors. (I would try -20 to start)
If your EGT is a k-type thermocouple, then you can log it with the T-Pro. But you will need the EGT amplifier found at fullthrottlespeed.com


-Rogue

you have to sacrifice the Aux wire and feature to use egt correct? its either 1 or the other

[JonVr4]

I am basically starting from square A, I have a decent understanding of the system. I am just lost on the setup of 5.0 software. I have the .s19 file loaded, the adl file loaded, I am not sure if I got the xdf loaded properly

Id appreciate someone chimmin in or even if there is a link to read. I got this from the 5.0 manual but there is nothing distinguished for my car.

Vehicle- 1
Disp- 3.08 ( I have it over bored)
Afsource- speed density
Mapsource-gmbar
Loadsource- use map
Baro- sea level
f-out- off
vout1- set max setting?
Vout2- sex max setting?
Afsource- lc1
Fin mode- 0 or 22 ? I don’t have timing installed
Aux1 mode- 11 ? for boost settings?
F out- 0

Mainscale- -20
V-out max1- ?
v-out max2- ?
afterstart- 5.0
lo load- 36
mid load- 100
high load- 143
tm base- ?
tm correction- ?
af delay- ?

air temp- ?
aux trigger- ?
tune response- ?

[Rogue_Ant]

Originally Posted by JonVr4

I also dont have the timing wired or anything, i should just load this bin and adjust the main scale and be ready to go? The bin loads the pt tracking/setup/configure/ and everything else?

Change the vehicle select to '1', since you're not using direct timing adjustment.
Otherwise the .bin is from Bob's Stealth, and should be a good base. (make sure you adjust the mainscale)


-Rogue

[Rogue_Ant]

Originally Posted by 3000GT MR

you have to sacrifice the Aux wire and feature to use egt correct? its either 1 or the other

Yes the EGT uses the Aux wire. However as long as you're just logging EGT, you can still use the new load-based timing feature. Load-based timing is only effected if you're using the Aux as a trigger.


-Rogue

[Rogue_Ant]

Originally Posted by JonVr4

I am basically starting from square A, I have a decent understanding of the system. I am just lost on the setup of 5.0 software. I have the .s19 file loaded, the adl file loaded, I am not sure if I got the xdf loaded properly

Id appreciate someone chimmin in or even if there is a link to read. I got this from the 5.0 manual but there is nothing distinguished for my car.

Vehicle- 1
Disp- 3.08 ( I have it over bored)
Afsource- speed density
Mapsource-gmbar
Loadsource- use map
Baro- sea level
f-out- off
vout1- set max setting?
Vout2- sex max setting?
Afsource- lc1
Fin mode- 0 or 22 ? I don’t have timing installed
Aux1 mode- 11 ? for boost settings?
F out- 0

Mainscale- -20
V-out max1- ?
v-out max2- ?
afterstart- 5.0
lo load- 36
mid load- 100
high load- 143
tm base- ?
tm correction- ?
af delay- ?

air temp- ?
aux trigger- ?
tune response- ?

Jon, take a look at the settings in the .bin I attached earlier. If you still have questions, I will be happy to answer them.


-Rogue

[xteekayx]

Guys where can I buy the original harness for MAF-T PRO that has 10pin connector on it.... the one in the car is too short and i can't put it in the glove box ... i looked on fullthrottleracing and can't find it. let me know, thanx ....

[Rogue_Ant]

If you call FTT, or email Mike at FTT he should be able to get you one.


-Rogue

[flyman1981]

Originally Posted by xteekayx

Guys where can I buy the original harness for MAF-T PRO that has 10pin connector on it.... the one in the car is too short and i can't put it in the glove box ... i looked on fullthrottleracing and can't find it. let me know, thanx ....

FYI - I just called today for the same thing (10pin + 6pin harness). They are a special order item. She is going to get me a price within 24 horus and said 7-10 days for delivery. I'll post back up when i get it.

They are also going to replace my top cover FOC because it warped from the heat. AWESOME customer service!