---===The Official MAFT-Pro Thread===--- - Page 110 - 3000GT/Stealth International Message Center

TurboBob · 06-22-2006, 12:11 AM

files:..........................

Maximal · 06-22-2006, 07:46 AM

Will it work if I leave it in AFC mode and just add the wires for timing?

Terry

TurboBob · 06-22-2006, 08:26 AM

yes.

The part throttle closed loop does not work in AFC mode yet, thats another loose end......

Bob

Maximal · 06-22-2006, 08:36 AM

Quote:

Originally Posted by TurboBob

yes.

The part throttle closed loop does not work in AFC mode yet, thats another loose end......

Bob

I plan on going speed density at some point anyways...just need to make a custom intake. This might be a good reason to do it.

Am I gonna run into any issues with speed density since I'm NA?

Terry

TurboBob · 06-22-2006, 08:41 AM

Quote:

Originally Posted by StealthES418

Am I gonna run into any issues with speed density since I'm NA?

Terry

I don't think so. Lets do it in stages, to be sure there are no hickups.

You won't need a 3 bar sensor, a 1 bar would do it. I haven't run it with a 1 bar sensor, but I run the 5 bar on my Stealth and it works fine....

Bob

Maximal · 06-22-2006, 08:49 AM

Quote:

Originally Posted by TurboBob

I don't think so. Lets do it in stages, to be sure there are no hickups.

You won't need a 3 bar sensor, a 1 bar would do it. I haven't run it with a 1 bar sensor, but I run the 5 bar on my Stealth and it works fine....

Bob

Already bought the 3 bar sensor...I'm assuming that'll still work?

Any chance you can PM the steps of these stages?

Terry

TurboBob · 06-22-2006, 08:53 AM

Well, the 3 bar is easy......

The stages were just get the sensors on and installed while still in AFC mode and then switch over once everything was happy......

Bob

Quick Vr4 · 06-22-2006, 10:51 AM

Anyone get the timing control running yet? I am kinda confused on how to hook it up. Do i need to buy a new harness? Which pin to tap into. Can we get a writeup.

TurboBob · 06-22-2006, 12:16 PM

this may make it clearer

If you PM'd me your address for the additional timing wire, I don't have it any more. Can you PM it again?

Bob

Quick Vr4 · 06-22-2006, 12:24 PM

ok that makes it clearer. The ITC uses the crank angle signal and cam angle signal. So I am only going to use the crank angle sensor for the maftpro? Isn't it the same as the TDC sensor?

06-22-2006, 07:46 AM	#1092 (permalink)
Maximal Supporting Vendor Join Date: Jan 2002 Location: Painted Post, NY Drives: '91 Stealth "ES" Trader Rating: (184)	Re: ---===The Official MAFT-Pro Thread===--- Will it work if I leave it in AFC mode and just add the wires for timing? Terry __________________

06-22-2006, 08:26 AM	#1093 (permalink)
TurboBob Resident mad scientist Join Date: Jan 2003 Location: Near Detroit Drives: 86 GN 91 RT/TT Trader Rating: (17)	Re: ---===The Official MAFT-Pro Thread===--- yes. The part throttle closed loop does not work in AFC mode yet, thats another loose end...... Bob

06-22-2006, 08:53 AM	#1097 (permalink)
TurboBob Resident mad scientist Join Date: Jan 2003 Location: Near Detroit Drives: 86 GN 91 RT/TT Trader Rating: (17)	Re: ---===The Official MAFT-Pro Thread===--- Well, the 3 bar is easy...... The stages were just get the sensors on and installed while still in AFC mode and then switch over once everything was happy...... Bob

06-22-2006, 10:51 AM	#1098 (permalink)
Quick Vr4 Forum Member Join Date: Oct 2002 Location: Southern California Drives: 91 3000gt VR4 Trader Rating: (11)	Re: ---===The Official MAFT-Pro Thread===--- Anyone get the timing control running yet? I am kinda confused on how to hook it up. Do i need to buy a new harness? Which pin to tap into. Can we get a writeup. __________________ R.I.P 20g VR4

06-22-2006, 12:24 PM	#1100 (permalink)
Quick Vr4 Forum Member Join Date: Oct 2002 Location: Southern California Drives: 91 3000gt VR4 Trader Rating: (11)	Re: ---===The Official MAFT-Pro Thread===--- ok that makes it clearer. The ITC uses the crank angle signal and cam angle signal. So I am only going to use the crank angle sensor for the maftpro? Isn't it the same as the TDC sensor? Last edited by Quick Vr4 : 06-22-2006 at 12:28 PM.

Sponsored Links
3000GT/Stealth International Message Center Advertisement

LinkBacks (?) LinkBack to this Thread: http://www.3si.org/forum/f103/official-maft-pro-thread-290438/
Posted By	For	Type	Date
HOW TO INSTALL MAFTPRO ON A 91-99 3000GT VR4/91-96 STEALTH TT	This thread	Refback	04-13-2008 01:45 AM