|
|
|
06-08-2008, 12:25 PM
|
#1 (permalink) |
|
Verified Seller
|
MAP ECU load time?
Trying to load a map onto MAP ECU (file - - > open data file?)
Then connect -- - > it says "writing line 19 18 17" etc. then it just says reading data for... 20minutes and counting now. Is that normal? Also, how do I know if it saved the map?
__________________
Go:DR650's, Stage 3 heads, webcam street/strip cams, ferrara 1mm oversized valves w/high rev kit, built block, 550cc injectors, MAP ECU, IPS FMIC kit, koyo radiator, twin flexalite fans, IPS radiator pipes, Dejon twin intake, kormex output shaft, RPS street max, e2k xfer case bracket, fidanza flywheel, stillen cross drilled/ slotted rotors (front & rear), eibach prosport lowering springs (1 & 1.5drop), atr dp, custom dual 2.5" catback, gutted precats,hks ssbov,hks boost controller, maximal solid motor mounts, setrab oil cooler, 3sx SS clutch line, ohio seattle throw shifter w/ solid bushings
Show: Cianci pillar, cobalt boost guage, cobalt air/fuel ratio guage, cobalt oil pressure gauge, cusco rear struct bar, 99 conversion (complete), deftspyer CF hood, clear turn signals, momo steering wheel, battery relocation, tint, momo shift knob/shift boot, 3sx engine dress up kit, 5zigen FN01RC's, Sparco Torino seats Weight reduction: Rims, seats, exhaust, cf hood, DELETE: Egr, vac reduction, AC, cruise control, both washer fluid resevoirs, battery tray and bracket, SRS system, Active exhaust+all wiring, active aero+all wiring, all heat shields, both impact beams, fog lights, rear seats, front and rear seatbelts, clutch booster canister and lines, hood latch, stock alarm, hood pistons And much, much more. --> |
|
|
| Sponsored Links | |
Advertisement |
|
|
06-08-2008, 02:56 PM
|
#3 (permalink) |
|
Verified Seller
|
Re: MAP ECU load time?
k well off to work now and total failure. It's acting as if there is no map in there at all. (550cc injectors running off stock ECU = black smoke)
I do what i mentioned previously, i load it , make sure its connected. Then I open the map (file - - > open data file) then i connect - it writes the lines, and then gets frozen on reading data for 2 hours 20 minutes before. I saved the file and tried to start the car, same thing - running off stock ECU it seems. Everything is connected fine, we just went over it today. What am I doing wrong? Hopefully while i'm gone someone can help me out. Thinking of once again ditching this for SAFC. |
|
|
|
|
06-09-2008, 01:32 AM
|
#4 (permalink) | |
|
Forum Member
|
Re: MAP ECU load time?
Quote:
Once its written all the lines, thats it! It then goes and says reading data- its waiting for you dude! If you saved the file of the net what you do is disconnect from the ecu. Go file, open and ope the datas file you got. Now press connect and it will go writing line 17,16, 15 etc. When it says reading data, its done and you can start up the car. You will find that whilst a base map will let you start the car, you do have to tune it from there. Cheers, Ben.
__________________
Ben H.
1st Gen GTO. DR800's, DR Stage 3 Heads, DR Ported lower Plenum, Wiseco Pistons, Crower Rods, FMIC, 680s, Arc2, Apexi SAFC, Blitz DSBC, Nomad BOV,K&N, F & R Strut Bars, Tein Flex coilovers, Stillen Brakes, Custom Exhaust, RPS Carbon-Carbon clutch, Custom fuel lines, 310lph pump, Samco Hoses, Viper Pilot Oil Cooler, Pitroad M Front end, 99 Combat Wing. 10.88@129.89 |
|
|
|
|
|
06-09-2008, 02:34 PM
|
#6 (permalink) | |
|
Verified Seller
|
Re: MAP ECU load time?
Quote:
I'm just switching to an SAFC, something is just wrong with my MAP ECU or i'm a moron or both heh. Pretty lame. |
|
|
|
|
